| Solutions Library
 Do
you have a problem and are looking for a solution?
TRACERCO Diagnostics™ services are used during
commissioning trials, trouble-shooting exercises, inspection
programmes and optimisation trials to allow our customers
to "look" inside their vessels to assess the actual
process conditions.
TRACERCO™ Instruments, which are extremely
low maintenance, are used when difficult measurements, due
to process fluids and operating conditions, are required
in real-time.
If you are experiencing similar problems to those listed
below please click on the problem to find out which of Tracerco’s
products or services can help your process;
How
can I detect deposits in my subsea pipeline?
How
can I find an untagged pig that is lost in a pipeline?
How
can I assess the amount of deposit in my subsea pipeline?
How
can I check the integrity of my members?
Have
the nozzles come off my burners?
Are
the tubes in my exchanger fouling?
How
can I ensure the integrity of my radioactive source during
logging whilst drilling operations?
Paying
too much for services such as steam, water and fuel?
Is
your flare header system free of blockage or buildup?
Do
you know how much material is in your transfer lines?
What
antifoam is best for my system?
Is
your catalyst getting deactivated or is there internal by
passing or leakage?
Which
of the bank of heat exchangers is leaking?
My
product is off-spec….
These
methanol drums should all be made from 20swg material. Some
have been made from 20swg material. How can I tell which
is which without removing the paint?
Is
my settling tank efficient?
How
do I find a leak in my brine reservoir?
How
can I monitor corrosion in my heat exchanger-offline?
How
can I check for corrosion under lagging?
I
have a leak in a pipe but the pipe is under 3ft of concrete.
Do I have to dig it all up to find the problem of the leak?
Does
the gate valve operate?
How
do I know that the refractory in my transfer lines has been
fabricated correctly and does not contain voids?
What
happens to the effluent when it leaves my plant and goes
into the river?
I
think I am getting overcharged for discharges….
Do
you have sand build-up in your vessel?
Do
you have slugs in pipes?
Does
your separator experience foam buildup?
Does
your separator experience poor separation?
Does
your separator experience oil in water measurement?
Do
you have instrument damage?
Is
my umbilical leaking?
How
can I confirm a blockage within a tower?
Is
there a technique available to confirm vapour cross-flow
channels?
I
suspect maldistribution in a packed bed. How can I confirm
my suspicions?
A
surge on the tower has damaged an indefinite number of trays.
How can I investigate the extent of the internal damage
of the tower?
How
can I quantify and identify the extent of a leak from a
reboiler system?
How
can I check if the exit nozzles on the vessel are becoming
choked or restricted?
I am experiencing excess carryover from a packed bed tower...
After
major internal modifications to separation vessels, how
can I evaluate how successful the modifications have been?
Due
to stringent environmental legislation, I need to determine
our flare gas rates...
How
can I feel confident that the heat exchangers on our site
are operating at optimised performance?
How
can I track a pig in a pipeline?
Is
your flow distribution through the reactor achieving its
theoretical yield?
We
have a problem producing and maintaining an even fluidisation
of catalyst and gas between the catalyst regenerator and
the reactor...
How
can I investigate the dramatic increase in the water concentration
in the ethylene glycol product stream?
How
can I determine the coke thickness in a FCCU?
How
can I determine the flow in my stream and verify some existing
flow meters?
How
can I prevent loss of efficiency and measure steam utilisation?
How
can I determine the cause of lost efficiency in my column?
How
can I locate a dislodged tray avoiding a shutdown?
How
can we diagnose the cause of poor tower performance?
How
can I detect a blockage in a reboiler?
How
can I detect pipeline scale and blockage in the line?
How
can I measure the bypassing in a feed/effluent exchanger?
How
can I determine evidence of gas bypassing through IS reactor?
Can
you pinpoint a leaking valve that is losing material?
Can
you identify a leaking waste heat boiler?
Do
you have an operational problem within packed bed section
of a separation column?
How
can I detect on-line leaks for better shut down scheduling?
How
can I detect a leak on a distillation column reboiler system?
How
can I identify packed bed damage?
How
can I boost the production yield in the reactor?
I
need a solution to polyethylene overflow problem...
Is
it possible to measure flow maldistribution?
How
do I detect a leaking converter bypass valve?
We
suspect internal damage/high metal content in a distillation
column...
I
think my feed/effluent exchanger may be leaking...
Can
we repair our pipeline without emptying/depressurising?
It
is important to have on-line measurement and control within
our separator vessel...
Can
I identify the location of a damaged spindle?
|
